BEZEL "GINGER"

Send

To complete this decoration you will need:
- an electrical appliance for burning on fabric.
- synthetic fabric of red color and golden veil.
- templates for petals and leaves from a can.
- a small piece of glass.
- a little green fabric in two shades.
- wire.
- A small foam base in the shape of an egg.
- Moment glue.
- any small decorations for the middle of the flowers.
- hair band.
- thin ribbon for the rim.
- a strip of dense fabric for the base.
- scissors.
- iron ruler.
Now we will prepare the main tool for work. Take a guilloche machine with a needle for fabric and glass.

For the colors, a non-transparent, ginger-colored fabric and a thin golden shade of a veil were chosen. From any tin can cut out the template for the petals. The base will be a square with a side of 6 cm. On one side, cut out a figure similar to a flame with 3 languages, and on the opposite side we make small narrowings from below. Then we put both fabrics together and with a hot needle we circle 19 blanks according to the template.

And for the leaves, the template is 5 cm high and 3 cm wide, in the form of a boat with a blunt end on one side. The leaves will also be of double fabric, and 5 pieces will need to be cut.

From the same fabric, cut out with a needle two rectangles, no longer than 5 cm and of different widths. We cut the fringe into them by applying a ruler.

And then green blanks need to be given a new shape. You need to put two pieces with a fringe together and with your fingers just scroll the cut side a little. On the leaves you can burn out not complex patterns. On one side of the sheet, we make dents along the edge, and on the second half we cut out several holes in the form of drops and dots. And at the end, fold the leaves in half, making a fold.

And now we turn to the flower petals, which need to be given extra volume. It is necessary to make oncoming folds on the basis of the blanks and solder them together with a needle. All petals are treated equally.

In addition, we cut out two strips measuring 5 x 2 cm from the fabric for the petals. And we divide them diagonally in half. And on the edges of the resulting triangles we make small notches.

Because when twisting, an interesting shape is obtained.

And you also need a sepal in the shape of an irregular star with 6 angles.

Cut 2 circles with a diameter of 3 cm, which will serve as the basis for the flowers. Now let's start the assembly. For one flower, take 8 petals and a circle. We will fasten to the base with a needle. The first row will be of 4 blanks located on the outer edge of the circle.

The remaining 4 petals are soldered in a checkerboard pattern, closer to the middle of the circle. The center remains free.

Both flowers are performed similarly.

Now it remains to choose jewelry for the middle in flowers. Take 2 large beads, stamens, balls or cones. Everything can be selected as you wish.

And glue in the middle, nicely positioning on the flower.

But we still need a bud and for this we take a wire 10 cm long. We take a foam base in the form of a quail egg, although it can be replaced with a foil blank, and we glue it well on the wire.

From the remaining 3 petals we collect a dense flower bud. The first blank completely covers the base, and the rest can be lubricated with glue on half the petal. The top edges will be free.

Then you need to attach 4 sharp blanks from the bottom in a circle and glue the sepal on top of everything.

It remains only to stick a thin tape over the wire, the bud is ready.

Now we turn to the processing of the rim, which will serve as the basis for the entire composition. The rim itself is glued with ribbons of two colors to the tone of the whole composition, but it is also possible with one tape. Then, from a strip of dense fabric, cut out 2 rectangles measuring 8 x 2.5 cm.

We round off the edges, and fold one part in half along the length and make cuts on the bend. 2 notches, with an interval of 1 cm, closer to the edges. Then we pass the rim through these holes. Next, the second part is glued to the first. It is necessary to take into account that this workpiece is located at least 10 cm from the edge of the rim.

Now you should start assembling the entire composition. Let's start with the bud. 4 cm from the top of the base on the rim and fasten the bud itself with glue. And we attach the wire to the rim with a thin tape. The rest of the wire is glued to the base.

Next we have green leaves, 4 will be on the base, and one in front of the bud. Then we glue the wide fringe onto the wire in front of the bud, and a small piece will be on the other side of the base between the leaves.